Feeler Gauge Set With 45 Degree Ends- Metric Feeler Gauge Set for setting valve clearances.
9pc. Set (marked in metric sizes only).
0.229mm. - (.009")
0.381mm. - (.015")
0.406mm. - (.016")
0.432mm. - (.017")
0.457mm. - (.018")
0.483mm. - (.019")
0.508mm. - (.020")
0.533mm. - (.021")
0.660mm. - (.026")
Part #: 35-1766

Blind Hole Bearing Puller Set

Includes 2.15LB Slide Hammer With Shaft & 8 Pc Of Bearing Collets.

Pulls The Following Size Bearings: 8-10mm, 10-12mm, 12-14mm, 15-17mm, 17-20mm, 20-24mm, 25-29mm, 30-32mm
Part #: 35-8010

8 pc. Driver Set for Allen Socket Screw

Hard to find deep 140mm. Long bits ideal for reaching up
inside lower fork legs and other recessed spots. Kit includes
1/2" drive socket sizes 5, 6, 7, 8, 10, 12, 14 & 17mm.
Part #: 35-9049

Rotor and Sprocket Holder. Keeps rotors, flywheels and sprockets from rotating during removal and installation. The adjustable stop-screw keeps the tool open at a set distance. Holds sprockets and rotors with holes center to center at a minimum distance of 13mm and a maximum distance of 230mm's.
Part #: 35-9121

Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Part #: 35-9122

Steering Head Bearing Race Remover, Range 25-35mm ID.

This tool will assist in removing motorcycle steering head bearing races. The size range is from 25mm to 35mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Part #: 35-9123

Aluminum Timing Degree Wheel

7" Diameter with Large Visible Markings. This Tool Allows for Extremely Accurate Marking which Makes Getting the Timing Right the First Time a Breeze! Lightweight and Durable Tool.

This Tool Can be used for Crankshaft Positioning, Ignition and Camshaft Timing.
Part #: 35-9126

Pilot Jet Set of 4 (Size #35). Jet Height 28mm, Outer Diameter 5.5mm.

Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets.

We list the stock Pilot Jet Sizes that came with the bikes below, you can use this list as a reference if you are trying to increase/decrease or keep the pilot jet size stock. We offer other sizes (above/below this part listing).

Honda CB750K (1969-76) - Stock Size 40,
CB750F (1975-76) Supersport - Stock Size 40
Part #: 48-3100

Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors.

Adjustable Width: 16-78mm and Adjustable Height 0-40mm
Part #: 35-0043

10 Piece Combination Flywheel Puller Driver Set. Used to separate flywheel from the crankshaft taper. Supplied in a labelled plastic storage case.

This 10 pieces set provides 15 different applications, sizes as follows：
M14x1.5, M16x1.5, M18x1.5, M19x1.0, M20x1.0, M27x1.25, M22x1.0, M25x1.5, M22x1.5, M26x1.5, M24x1.0, M27x1.0, M26x1.0, M28x1.0, M28x1.5

Except for M27X1.0, all applications have right hand threads.
Part #: 35-0074

Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2, 3 or 4 cylinders.

Includes 4 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Part #: 35-0085

Feeler Gauge Set - Metric Feeler Gauge Set for setting valve and contact point clearances. 20pc Set (marked in metric sizes only).
0.05mm. - (.002") 0.55mm. - (0.22")
0.10mm. - (.004") 0.60mm. - (0.24")
0.15mm. - (.006") 0.65mm. - (0.26")
0.20mm. - (.008") 0.70mm. - (0.28")
0.25mm. - (.010") 0.75mm. - (0.30")
0.30mm. - (.012") 0.80mm. - (0.32")
0.35mm. - (.014") 0.85mm. - (0.34")
0.40mm. - (.016") 0.90mm. - (0.36")
0.45mm. - (.018") 0.95mm. - (0.38")
0.50mm. - (0.20") 1.00mm. - (0.40")
Part #: 35-1768

Ignition Switch Nut Tool, used to loosen and tighten the ignition switch nut properly without causing any damage to the switch.

Fits: Honda CB750K (1969-76) Ignition Switch
Part #: 35-9119

Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed.

Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Part #: 35-9120

JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3.

Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face.

It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!
Part #: 35-0047

Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter.

Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Part #: 35-0064

"Tuck Away" 18mm Spark Plug Wrench. Works on 18mm Spark Plugs, 160mm overall, thinwall design allows fit into the deep CB plug holes. Handle Tucks away into socket.

Fits: 18mm Spark Plugs,
All Honda CB750's (1969-78)
Part #: 35-0078

Feeler Gauge Set - Metric/Inch Feeler Gauge Set for setting valve and contact point clearances. 31pc Set (marked in metric and inch sizes).
0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025")
0.08mm. - (.003") 0.10mm. - (.004") 0.13mm. - (.005")
0.15mm. - (.006") 0.20mm. - (.008") 0.23mm. - (.009")
0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012")
0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015")
0.40mm. - (.016") 0.43mm. - (.017") 0.45mm. - (.018")
0.48mm. - (.019") 0.50mm. - (.020") 0.53mm. - (.021")
0.55mm. - (.022") 0.58mm. - (.023") 0.63mm. - (.025")
0.65mm. - (.026") 0.70mm. - (.028") 0.75mm. - (.030")
0.80mm. - (.032")
Part #: 35-1769

40 pc. Metric Tap & Die Set in storage case.
Set includes Pitch Gauge, Die Holder, 2 Tap Wrenches & screw driver +

Metric Taps - M3 x 0.5, M3 x 0.6, M4 x 0.75, M4 x 0.7, M5 x 0.8, M5 x 0.9,
M6 x 1.0, M6 x 0.75, M7 x 0.75, M7 x 1.0, M8 x 1.0, M8x 1.25, M10 x 1.25,
M10 x1.5, M12x 1.25, M12 x 1.5, 1/8NPT x 27

Metric Dies - 17 Dies to match taps listed above.
Part #: 35-8030