Hide Categories

Series 1: Electrical

For Electrical Parts - Please see our Terms of Service located at the bottom left hand corner of every page.
USD$89.95 ea

Dynatek Charge Monitor

Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems.

The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing.

High quality made in the USA. Comes with a one year warranty through the manufacturer.
Part #: 07-9976
USD$199.95 Kit

Dynatek Dyna S Ignition System

Dynatek Dyna S Ignition System.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9988
USD$339.00 Kit

Dynatek Dyna S Ignition System (Premium Kit)

Dynatek Dyna S Ignition System (Premium Kit) with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9987
USD$409.95 Kit

Dynatek Dyna S Ignition System (Ultimate Kit)

Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9986
USD$479.00 Kit

Dynatek Dyna 2000 Digital Performance Ignition

Dynatek Dyna 2000 Digital Performance CDI Ignition.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9994
USD$609.00 Kit

Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)

Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9993
USD$689.00 Kit

Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)

Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek 3 Ohm coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9992
USD$189.95 Set/2

Dynatek Performance High Output 3 Ohm Ignition Coil Set/2

Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9980
USD$214.95 Kit

Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires

Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user.

Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9974
USD$189.95 Set/2

Dynatek Performance High Output 5 Ohm Ignition Coil Set/2

Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9979
USD$26.95 Set

Dynatek Performance Spark Plug Wire Set

Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core.

4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user.

Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA.

Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Part #: 07-9978
USD$39.95 ea

Ignition Coil

Ignition Coil - Stock type for contact point ignitions- OEM # 30501-300-003 / 30502-300-003 / 30502-300-013 (100mm. c-c mounting points)

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic

Note: 2 Coils Used per Bike, Order the Quantity you Require
Part #: 17-6823
USD$94.95 Set/2

Stock Type Ignition Coil Set/2 With Brackets

Stock Type Ignition Coil Set/2 With Brackets. Replaces OEM# 30500-300-013

Dual Coil Assembly Pre-Mounted on their Brackets Just Like the Stock Type. Plug and Play Easy Install. Primary 4.3 Ohm, Secondary 15,000k Ohms.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 65-6507
USD$74.95 ea

XS Performance High Output Coil

XS Performance Dual Output Ignition Coil

Fits: Honda All Honda CB750's (1970-78)

Dual Tower XS Performance High Output ignition Coil 3.3 OHM Primary Resistance. 15K OHM Secondary Resistance. Capable of sustained 45KV output with 12.5v DC input. Capable of sustained 75KV output with 14v DC input. Replaces stock factory ignition coils on All 1970 & up models and works with Pamco electronic ignitions. Requires 7 mm Dia. High tension spark plug wires (order separate) and 5K OHM spark plug caps. CB750's require 2 coils.
Warning! Serious High Voltage

WARNING!!! Do not operate or apply power to the ignition system with one or both spark plugs disconnected. Operating or applying power to the coil or ignition system with one or both spark plugs disconnected will cause IMMEDIATE FAILURE to the coil. Ignition coils are NOT WARRANTIED for this reason.

Note: 2 Coils Used per Bike, Order the Quantity you Require
Part #: 17-6810
USD$64.95 ea

Ultimate High Output Coil

Ultimate High Output Coil (not for points systems)

This coil is not suitable as a replacement coil as it is not compatible with points. Dual output coils do not have polarity, so power feed wires can go to either terminal.

This coil produces 82,000 volts to the spark plugs for a hotter and longer lasting spark for faster starts, better fuel economy and more power. When used with an aftermarket electronic ignition system, like the PAMCO, you will experience the true potential of your CB750, CB500 or CB550.

Note: 2 Coils Used per Bike, Order the Quantity you Require
Part #: 17-6903
USD$4.95 Set

Ignition Coil and Cap Seal Set

Replacement coil tower Caps and Seals set. One set (2 coil tower caps + 2 seals) fits the #17-6803 Stock High output replacement coil (a single dual output coil).
Part #: 17-6804
USD$2.95 Pk/2

Replacement Coil Tower Boots

Coil Tower Boots for XS Performance Green Coil (Pk/2)

Fits: XS Performance Green Coils #17-6810 (Above)
Part #: 17-6830
USD$2.25 Pk/2

Coil High Tension Wire Ends (Pk/2)

Coil High Tension lead ends (fit inside coil towers) (Pk/2)

Fits: XS Performance Green Coils #17-6810 (Above)
Part #: 17-6831
USD$12.95 Set/4

Coil Wire Set

7mm. Spark Plug Wire Set (4pc.) - Original Type Wire - Black Color with Copper Core. Silicone rubber casing. Each pc. 20" Long.

Fits: to stock coils or Aftermarket Performance coils.
Part #: 23-2908
USD$14.95 Set/4

Performance Silicone Plug Wires

Performance 7mm. Spark Plug Wire Set (4pc.) - Yellow Color with Copper Core. Silicone rubber casing. Each pc. 20" Long.

Fits: to stock coils or Aftermarket Performance coils.
Part #: 23-2909
USD$11.95 ea

Ignition Coil Holder Clamp

Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic

Note: Sold Each, 2 Used Per Bike, Order the Quantity you Require
Part #: 73-0886
USD$24.95 ea

Ignition Switch

Ignition Switch - Fits: Early CB750 - Round Plug (6 Hole, 4 wire) type.
Replaces OEM# # 35100-303-007 / 35100-292-003 / 35100-292-013

Fits: Honda CB750K (1969-72) with round wire harness to switch connector plug.

Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch
Part #: 12-0060
USD$34.95 ea

Ignition Switch

Ignition Switch with fork lock and keys - OEM Ref. # 35010-377-007 / 35100-377-003/007 / 35100-422-017 / 35100-438-007

Fits: Honda CB750K (1977-78)
CB750F (1975-78) Supersport,
CB750A (1976-78) Automatic
Part #: 12-0051
USD$21.95 ea

Ignition Switch

Ignition Switch, Square 4 Prong Plug Type. Replaces OEM # 35100-374-007 / 35100-369-740 / 35100-341-700

Fits: Honda CB750K (1973-76) with square wire harness to switch connector plug.

Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch
Part #: 12-0061
USD$13.95 ea

Universal Ignition Switch

Universal Ignition Switch, 3 Position Type with 2 Keys.

Will work with the mount bracket & cover below #12-0069 and mount bracket #12-0039
Part #: 12-0058
USD$10.95 ea

Switch Repair Kit

Honda Ignition Switch Base unit repair Kit (including base cover).

Fits: Ignition Switch Above (#12-0051)

PLUS: Honda CB750K (1977-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 12-0064
USD$3.00 ea

Switch Base Cover

Honda Ignition Switch Base Cover

Fits: Ignition Switch Above (#12-0051)

PLUS: Honda CB750K (1977-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 12-0065
USD$7.95 ea

Universal Ignition Switch Bracket

Chrome Universal Ignition Switch Bracket. Switch hole is 22.5mm, bolt hole is 9.5mm, overall length is 75mm.

Fits to our #12-0058 Sold Separate
Part #: 12-0039
USD$11.95 ea

Universal Ignition Switch Mount Bracket & Cover

Out of Stock
Universal Ignition Switch Mount Bracket & Cover
Universal Ignition Switch Mount Bracket & Cover

Will work with the ignition switch above #12-0058
Part #: 12-0069
USD$21.95 ea

Ignition Switch Mounting Bracket & Hardware Set

Ignition Switch Mounting Bracket & Hardware Set. Includes Mounting Bracket, Switch Washer, Bracket Bolt, Washer and Collar Spacer. Replaces Mounting Bracket OEM # 50375-300-000B

Fits: Honda CB750K (1969-76)
Part #: 73-1118
USD$7.95 ea

NGK Spark Plug Cap

NGK Spark Plug Cap - SD05F -

Fits: 2 Inner cylinders on All Honda CB750's (1969-78)

2 required per CB750
Part #: 23-3115
USD$7.95 ea

NGK Spark Plug Cap

NGK Spark Plug Cap - XD05F -

Fits: 2 Outer cylinders on All Honda CB750's (1969-78)

2 required per CB750
Part #: 23-3119
USD$6.50 ea

NGK Spark Plug

NGK D8EA Spark Plug - Standard Original CB750 Spark Plug

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic

4 required per CB750
Part #: 50-8600
USD$16.95 ea

NGK Iridium Spark Plug

NGK DR8EIX Iridium Spark Plug

Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike!

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic

4 required per CB750
Part #: 50-8605
USD$7.95 ea

Condenser

Condenser OEM # 30250-300-154 / 30250-300-005 (2 required for CB750).

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Automatic,
CB750P (1976-78) Police

2 Required Per CB750
Part #: 26-5104
USD$8.00 ea

Ignition Contact Points

Contact Point Set (1pc.) - Right Hand Side
OEM # 30203-300-005 / 30203-300-154

Fits: RIGHT HAND SIDE ONLY on All Honda CB750's (1969-78)
Part #: 14-0009
USD$8.00 ea

Ignition Contact Points

Contact Point Set (1pc.) - Left Hand Side
OEM # 30204-300-005 / 30204-300-154

Fits: LEFT HAND SIDE ONLY on All Honda CB750's (1969-78)
Part #: 14-0010
USD$3.50 Pk/4

Contact Point Screws - (Pk./4)

Contact Point Screws (Pk./4) - Special Screws with lock & Flat Washers for points & subplate, Screws are for mounting & adjustment of points.
Part #: 14-0190
USD$34.95 ea

Haynes Electrical Techbook

Haynes Electrical Techbook

From basic electrical theory to complex electronic systems, this manual meets the needs of the professional and amateur technician. All motorcycle electrical equipment fully explained. An information source for practicing technicians. Over 600 illustrations throughout the techbook. The clearly presented text is fully illustrated with photo's and diagrams. Clearly captioned step by step pictures show precisely how to perform tasks.

Features sections on - ignition and combustion explained, spark plug types and construction, ignition: magnetos, coil and battery, CDI, transistor and digital, fuel injection and engine management, alternators, DC generators and starters, batteries, lighting and signalling, braking and traction control systems, electrical fault finding and practical testing and test equipment.
Part #: 61-0061
USD$44.95 ea

Cast Aluminum Finned Points Cover

Cast Aluminum Finned Points Cover, Made in the USA. Replaces OEM # 30370-300-020

This is a new cover designed and produced like the ones from the 70's that aren't made anymore. This cover is delivered in as-cast condition. As such, Sandblasting, painting, or powder coating will be required if you want a look other then the cast aluminum look. As delivered it is a close match for an original patina engine.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic

Note: Gasket and Hardware Not Included with Cover
Part #: 73-1095
USD$99.00 ea

Custom Black Finned Points Cover ~ Joker Machine

Joker Machine Brand ~ Custom Black Finned Points Cover with a Built in Rubber O-Ring and Gold Colored Mounting Hardware, Replaces OEM # 30370-300-020

Brilliant "diamond cut" machining on the outside surface, really gives this piece a cool look! High quality CNC machined cover made in the U.S.A.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 73-1069
USD$2.95 Set/2

Points Cover Screws

Points Cover Screws (Set of 2).

Fits: ALL 1969-1978 Honda CB750 Points Covers and Our Points Cover above (Part #13-0000).
Part #: 73-0901