Hide Categories

Series 1: New Items

USD$1.50 ea

Drain Plug Washer

Drain Plug Crush Washer

12mm x 18mm x 1mm

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport
Part #: 15-0006
USD$1.50 ea

Drain Plug Washer

Drain Plug Washer

14mm x 20mm x 1mm

Fits: Honda CB750A (1976-78) Hondamatic
Part #: 15-0000
USD$3.95

Fork Leg Washer Set

Fork Leg Copper Washer Set (4)

8mm x 13mm x 1.5mm x 2pcs (OEM Ref 90544-283-000)
6mm x 10mm x 1mm x 2pcs (OEM Ref 90543-273-000)

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic,
CB750P (1976/78) Police
Part #: 15-0045
USD$99.95 ea

Shock Absorber Set ~ Stock 335mm Length

Shock Absorber Set - Chrome Body with Chrome Springs and Chrome End Cap - 335mm (13 3/16") Eye to Clevis. 4 Position spring preload adjustment, progressive wound heavy duty springs. Includes bushings, inserts, washers and spring preload wrench.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Automatic
Part #: 06-3588
USD$24.95 ea

Horn ~ Similar to Stock Style

Horn with Chrome Cover - 12 Volt 3 Amp - 103 Decibel - This is Not identical to the stock type but has a somewhat similar design to the stock type on these bikes.

Fits: CB750K (1969-76),
CB750F (1975-76) Supersport
Part #: 99-4994
USD$13.50 ea

Starter Solenoid Relay

Starter Solenoid Relay, Replaces OEM# 35850-371-670 / 35850-306/670 / 35850-HA7-670

Fits: Honda CB750K (1969-76),
CB750F (1975-76) Supersport,
CB750A (1976-78) Hondamatic
Part #: 09-6582
USD$4.95 ea

Signal Lamp Lens ~ Clear

Signal Lamp Lens - Clear - OEM # 33402-377-671

Fits: Honda CB750K (1975-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic,
Signal Lamp #11-2114 and #11-2149 (Above)
Part #: 11-2152
USD$4.95 ea

Signal Lamp Lens ~ Smoked

Signal Lamp Lens - Smoked - OEM # 33402-377-671

Fits: Honda CB750K (1975-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic,
Signal Lamp #11-2114 and #11-2149 (Above)
Part #: 11-2153
USD$5.95 ea

Tail Light Lens Gasket

Tail Light Lens Gasket - Replaces OEM# 33709-341-671

Fits: Honda CB750K (1972-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 11-2163
USD$10.95 ea

Foam Round Pod Air Filter

42mm Round Foam Pod Air Filter With Chrome End Caps and Rubber Mouth - Circular style.

Fits: Honda CB750K (1977-78),
CB750F (1977-78) Supersport

Please Double check you require 42mm Pod Filters before purchasing
Part #: 15-0165
USD$9.95 ea

Clutch Center Nut Removal Tool

Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport
Part #: 35-0051
USD$31.95 ea

CB750K 1969-70 Tachometer Face Plate

Tachometer Face Plate (Like Original)

Disassembly of tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

This face plate is supplied without jewels. You can re-use the jewels from the faces you replace or we sell those separately.

Fits: Honda CB750K (1969-70)
Part #: 73-0647
USD$49.95 ea

CB750K 1969-70 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

This face plate set is supplied without jewels. You can re-use the jewels from the faces you replace or we sell those separately.

Fits: Honda CB750K (1969-70)
Part #: 73-0654
USD$49.95 ea

CB750K 1971 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

This face plate set is supplied without jewels. You can re-use the jewels from the faces you replace or we sell those separately.

Fits: Honda CB750K (1971)
Part #: 73-0655
USD$44.95 ea

CB750K 1972 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1972)

Note: This is the rectangular style cutout (On the speedo the cutouts are rectangular shaped), we also carry a L-Cut style for the CB750K 1972, double check your speedo to see the style you require before purchase.
Part #: 73-0657
USD$44.95 ea

CB750K 1972-73 Speedo & Tachometer Face Plate Set ~ MPH

Out of Stock
Email Me When Available
CB750K 1972-73 Speedo & Tachometer Face Plate Set ~ MPH
Speedometer & Tachometer Face Plate Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1972-73)

Note: This is the rectangular style cutout (On the speedo the cutouts are rectangular shaped), we also carry a L-Cut style for the CB750K 1972, double check your speedo to see the style you require before purchase.
Part #: 73-0656
USD$44.95 ea

CB750K 1974 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1974)

Note: This is the rectangular style cutout (On the speedo the cutouts are rectangular shaped), we also carry a L-Cut style for the CB750K 1974, double check your speedo to see the style you require before purchase.
Part #: 73-0659
USD$44.95 ea

CB750K 1972-74 L- Cut Style Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate L-Cut Version Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1972-74)

Note: This is the L-Cut style (On the speedo the cutouts are L shaped), we also carry a standard style for the CB750K 1972, double check your speedo to see the style you require before purchase.
Part #: 73-0658
USD$44.95 ea

CB750K 1976 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1976)
Part #: 73-0660
USD$44.95 ea

CB750K 1977 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1977)
Part #: 73-0662
USD$44.95 ea

CB750K 1977 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1977)
Part #: 73-0661
USD$44.95 ea

CB750K 1978 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1978)
Part #: 73-0664
USD$44.95 ea

CB750K 1978 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750K (1978)
Part #: 73-0663
USD$37.95 ea

CB750F 1975 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1975) Supersport
Part #: 73-0648
USD$37.95 ea

CB750F 1976 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1976) Supersport
Part #: 73-0649
USD$37.95 ea

CB750F 1977 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1977) Supersport
Part #: 73-0651
USD$37.95 ea

CB750F 1977 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1977) Supersport
Part #: 73-0650
USD$37.95 ea

CB750F 1978 Speedo & Tachometer Face Plate Set ~ MPH

Speedometer & Tachometer Face Plate (Like Original) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1978) Supersport
Part #: 73-0653
USD$37.95 ea

CB750F 1978 Speedo & Tachometer Face Plate Set ~ KM/H

Speedometer & Tachometer Face Plate (Like Original) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required.

All face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750F (1978) Supersport
Part #: 73-0652
USD$44.95 ea

CB750A 1976 Speedo Face Plate & Gear Indicator Decal Set ~ MPH

Speedometer Face Plate (Like Original) & Gear Indicator & Fuel Meter Decal (Sticker) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required. Decals come uncut.

Removal of original information printed on OEM plastic face is required prior to application of these decals. All blue/green areas are the plastic face showing through.

All decals and face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750A (1976) Hondamatic
Part #: 73-0644
USD$44.95 ea

CB750A 1977 Speedo Face Plate & Gear Indicator Decal Set ~ MPH

Speedometer Face Plate (Like Original) & Gear Indicator & Fuel Meter Decal (Sticker) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required. Decals come uncut.

Removal of original information printed on OEM plastic face is required prior to application of these decals. All blue/green areas are the plastic face showing through.

All decals and face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750A (1977) Hondamatic
Part #: 73-0645
USD$44.95 ea

CB750A 1978 Speedo Face Plate & Gear Indicator Decal Set ~ MPH

Speedometer Face Plate (Like Original) & Gear Indicator & Fuel Meter Decal (Sticker) Set ~ MPH Type.

Disassembly of speedometer and tachometer is required. Decals come uncut.

Removal of original information printed on OEM plastic face is required prior to application of these decals. All blue/green areas are the plastic face showing through.

All decals and face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750A (1978) Hondamatic
Part #: 73-0646
USD$44.95 ea

CB750A 1977-78 Speedo Face Plate & Gear Indicator Decal Set ~ KM/H

Speedometer Face Plate (Like Original) & Gear Indicator & Fuel Meter Decal (Sticker) Set ~ KM/H Type.

Disassembly of speedometer and tachometer is required. Decals come uncut.

Removal of original information printed on OEM plastic face is required prior to application of these decals. All blue/green areas are the plastic face showing through.

All decals and face plates are "printed" in the United Kingdom on the highest quality materials. Every detail has been designed very accurately to achieve an exact copy of the original face plates. With this set you are able to restore your gauges to the manufacturers standards.

Fits: Honda CB750A (1977-78) Hondamatic
Part #: 73-0665
USD$18.95 ea

Speedometer Tripmeter Reset Knob

Speedometer Tripmeter Reset Knob, Replaces OEM# 37237-300-000

These buttons are often damaged and are no longer available from Honda. This reproduction knob is the finishing touch for your precious speedo meter. Fits to many speedos.

Made for 3mm shafts.

Fits: Honda CB750K (1969-72)
Part #: 49-0253
USD$134.95 Set

Two Metal Speedo / Tach Gauge Covers With Crimp Rings

Two Metal Speedo / Tach Gauge Covers With Crimp Rings.

These metal gauge covers are often dented, scratched and corroded. It takes a lot of time to remove the dents, scratches and repaint the covers. With this set of two reproduction gauge covers, you can recondition your gauges so that these will look like new!

These covers are unique and the best quality on the market (Made in the United Kingdom). The black metal covers are already painted in the right semi-gloss black colour and are ready to use.

This listing contains two black metal covers with crimp rings.

These covers lack the hole at the side for speedo meters with the trip meter reset at the side. This hole must be drilled if required.

Fits: Honda CB750K (1971-78),
CB750F (1975-78) Supersport
Part #: 49-0252
USD$37.95 Set/2

Speedometer & Tachometer Crimp Ring Set/2

Speedometer & Tachometer Crimp Ring Set/2. When changing the speedometer or tachometer face plates these rings are often damaged. Get a new set today to have your speedo & tachometer restoration looking perfect!

Dimensions: Inner diameter 102.7mm. - Outer diameter 107.5mm.

Fits: Honda CB750K (1971-78),
CB750F (1975-78) Supersport
Part #: 49-0249
USD$24.95 Set/2

Speedometer & Tachometer Replacement Glass Lens Set/2

Speedometer & Tachometer 92mm Glass Lens Set/2. If the glass lens of your gauges have scratches or are broken, with these glass lenses you are able to repair your gauges' lenses.

These glass lenses are slightly bent like the original glass lenses.

Fits: Honda CB750K (1971-78),
CB750F (1975-78) Supersport
Part #: 49-0250
USD$18.95 ea

Speedometer / Tachometer Glass Lens Rubber Seal

Out of Stock
Email Me When Available
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach.

Fits: All 92mm (3.6") glass lenses.

Sold each, order the quantity you require

Replaces 92mm Lenses on : Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 49-0248
USD$24.95 Set

Tachometer & Speedometer Jewel Set

Tachometer & Speedometer Jewel Set. Includes Four Jewels/Lenses: Red (Hi-Beam), Orange (Turn Signals), Green (Neutral) and Red (Oil Pressure).

Fits: Honda CB750K (1969-71)
Part #: 49-0251
USD$6.95 ea

Speedometer / Tachometer Internal Rubber Seal

Out of Stock
Email Me When Available
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal.

This internal rubber seal replaces the ripped, dried or missing rubber internal seal.

This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Part #: 49-0255
USD$9.95 ea

Trip Meter Knob Rubber Grommet

Out of Stock
Email Me When Available
Trip Meter Knob Rubber Grommet
Day Trip Meter Knob Rubber Grommet. These grommets are often dried out and ripped, get a new one today!

Fits: Honda CB750A (1976-78) Hondamatic
Part #: 49-0256
USD$249.95 ea

Front Brake Rotor

Front Brake Rotor, High Quality Made in Japan. Replaces OEM# 45120-392-000 / 45120-300-040 / 45120-341-000

Fits: Honda CB750K (1969-78),
CB750F (1975-76) Supersport,
CB750A (1976-77) Hondamatic
Part #: 30-3066
USD$38.95 ea

Carburetor Stabilizer Bracket

Carburetor Stabilizer Bracket. Comes with 7mm spacer and 30mm socket head cap screw. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!

Fits: Honda CB750K (1977-78),
CB750F (1977-78) Supersport
Part #: 29-0537
USD$26.95 ea

Speedo Gear Plug

Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long.

This Plug is Great for Keeping your Original Speedo Drive Gear Clean.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 29-0538
USD$29.95 ea

Side Cover Emblem 1978F

Out of Stock
Email Me When Available
Side Cover Emblem 1978F
Side Cover Emblem with 2 Attachment Clips. Replaces OEM# 87127-410-770

Fits: Honda CB750F (1978) Supersport

Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Part #: 48-9516
USD$19.95 ea

Aluminum Timing Degree Wheel

Aluminum Timing Degree Wheel

7" Diameter with Large Visible Markings. This Tool Allows for Extremely Accurate Marking which Makes Getting the Timing Right the First Time a Breeze! Lightweight and Durable Tool.

This Tool Can be used for Crankshaft Positioning, Ignition and Camshaft Timing.
Part #: 35-9126
USD$67.45 ea

Front Brake Master Cylinder Assembly

Out of Stock
Email Me When Available
Front Brake Master Cylinder Assembly
Front Brake Master Cylinder Assembly.

Black body with silver lever. Manufactured with a piston size of 14mm which is the stock size used on these bikes. They are designed to look similar to the original CB750 master cylinders listed below.

Fits: Honda CB750K (1969-77)
CB750F (1975-76) Supersport,
CB750A (1976) Hondamatic

will also work on the bikes below but this master cylinder does not have a brake light switch similar to the OEM type. So, you will need to purchase our #29-7002 hydraulic brake light switch to go with this assembly.
CB750K (1978),
CB750F (1977-78) Supersport,
CB750A (1977-78) Hondamatic

Note: The master cylinder reservoir cap above #29-0054 looks Great with this master cylinder and gives it more of an original look!
Part #: 08-4005
USD$29.95 Kit

Front Brake Caliper Rebuild Kit

Front Brake Caliper Rebuild Kit

Kit includes brake caliper sealing ring, caliper bolts X2, bleed screw, bleed screw cap, and brake caliper adjuster set consisting of adjusting bolt, spring, washer and nut.

Fits: Honda CB750K (1969-76)
Part #: 14-0505
USD$34.95 Kit

Front Brake Caliper Rebuild Kit

Front Brake Caliper Rebuild Kit

Kit includes brake caliper sealing ring, caliper bolts with washers X2, bleed screw, bleed screw cap, and brake caliper adjuster set consisting of adjusting bolt, spring, washer and nut.

Fits: Honda CB750K (1977-78),
CB750A (1976-78) Hondamatic,
CB750F (1975) Supersport,
CB750F (1976) Supersport (VIN# CB750F-2000003 TO CB750F-2022317) Only
Part #: 14-0506
USD$9.95 ea

Foam Round Pod Air Filter

Out of Stock
Email Me When Available
Foam Round Pod Air Filter
39mm Round Foam Pod Air Filter With Chrome End Caps and Rubber Mouth - Circular style.

Fits: Honda CB750K (1969-76)
Part #: 15-0095
USD$44.95 ea

Matte Black ~ OEM Type Gas/Fuel Tank Cap With Latch Assembly

Out of Stock
Email Me When Available
Matte Black ~ OEM Type Gas/Fuel Tank Cap With Latch Assembly
Matte Black OEM Type Gas/Fuel Tank Cap with Gasket, Hinge Pin (with E-Clip which Allows for easy installation) and Gas/Fuel Tank Cap Latch Assembly, Includes Latch, Return Spring, Latch Mounting Pin and C-Clip. Replaces OEM # 17510-323-310

Fits: Honda CB750K (1969-75)
Part #: 07-9967
USD$8.25 Set

Black Aluminum Handlebar End Plug Set

Black Anodized Aluminum Handlebar End Plug Set with Allen Key for Install.

These Reduce handlebar vibration, while adding a nice touch. Can be installed in seconds. Just pop them in to the open end of your grips and tighten the bolt with the included allen key.

These will fit into any 7/8" handlebars with open ends
Part #: 02-2433
USD$16.95 ea

Cam Chain Guide

Cam Chain Guide - Replaces OEM# 14611-312-000

Fits: Honda CB750K (1969-71),
CB750K (1972) - Engine Serial number Lower then 2200000 Only
Part #: 07-9966
USD$84.95 ea

Performance High Output 5.2 Ohm Coil

Performance Dual Output Ignition Coil - 5.2 Ohm Type with Hardware.

Fits: Honda All Honda CB750's (1970-78)

Dual Tower Performance High Output ignition Coil 5.2 OHM Primary Resistance. 17K OHM Secondary Resistance. Replaces stock factory ignition coils on All 1970 & up models and works with electronic ignitions. Requires 7 mm Dia. High tension spark plug wires (order separate) and 5K OHM spark plug caps.

Warning! Serious High Voltage

WARNING!!! Do not operate or apply power to the ignition system with one or both spark plugs disconnected. Operating or applying power to the coil or ignition system with one or both spark plugs disconnected will cause IMMEDIATE FAILURE to the coil. Ignition coils are NOT WARRANTIED for this reason.

Note: 2 Coils Used per Bike, Order the Quantity you Require
Part #: 07-9973
USD$14.50 Set

Ignition Coil Bracket Set

Ignition Coil Bracket Set. Replaces OEM# 30511-300-000

Features a high grade polished finish and includes coil mounting hardware.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-0190
USD$7.95 ea

Front Brake Pipe "B"

Front Brake Pipe "B" - Replaces OEM# 45128-300-010

Aprox 7 7/8" Total Length.

Fits: Honda CB750K (1969-71),
CB750K (1972) Upto Frame #2093730 Only
Part #: 07-9969
USD$9.95 ea

Front Brake Pipe "B"

Front Brake Pipe "B" - Replaces OEM# 45128-341-670

Aprox 7.5" Total Length.

Fits: Honda CB750K (1972) Frame #2093731 and Higher Only,
CB750K (1973-76)
Part #: 07-9970
USD$8.95 ea

Front Brake Pipe

Front Brake Pipe - Replaces OEM# 45128-323-020

Aprox 8" Total Length.

Fits: Honda CB750K (1977-78),
CB750F (1975-76) Supersport
Part #: 07-9971
USD$4.95 ea

Stock Type Front Reflector Rubber Base

Stock Type Front Reflector Rubber Base - Replaces OEM# 33743-341-670

Fits: Honda CB750K (1969-76)
Part #: 11-2304
USD$34.95 ea

Fuel Tank Emblem

Fuel Tank Emblem with 2 Attachment Clips - Replaces OEM# 87122-410-000 , 87121-410-000. High quality made of cast metal.

Fits: Honda CB750F (1977-78) Supersport

Note: Sold Each, Order 2 if replacing the emblems on both sides of the fuel tank.
Part #: 48-9512
USD$84.95 ea

Headlight Assembly

Out of Stock
Email Me When Available
Headlight Assembly
Chrome Side Mount Headlight Assembly.

Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart.

Halogen Lamp unit with 12v 60/55 Bulb (P43T base) and Bulb Dust Boot for North American Market CB750's that drive on the right side of the road.

Fits: All Honda CB750's (1969-78)
Part #: 09-0069
USD$84.95 ea

Headlight Assembly ~ European Version

Out of Stock
Email Me When Available
Headlight Assembly ~ European Version
Chrome Side Mount European Version Headlight Assembly.

Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart.

60/55 watt H4 P43T Halogen Bulb and parking light. E-Mark certified for European Market use (can also be used in North America).

Fits: All Honda CB750's (1969-78)
Part #: 09-0071
USD$39.95 ea

Black Tail Lamp Assy. - Custom British Style

Black Tail Lamp Assy. - Custom British Style with alloy mount bracket and license plate illumination.

These are perfect for many cafe and custom projects. Includes everything shown.

Lens Dimensions: 4-1/2" Wide, 2-1/8" High, 1-3/4" Depth

Full Assembly Dimensions: 7" Total Width, 5-1/2" Total Length, 3-1/2" Total Height
Part #: 09-0086
USD$12.95 ea

Established 2010 VintageCB750 T-Shirt

Black 100% Cotton T-Shirt with "Established 2010 VintageCB750 Logo" on the Front of the Shirt.

We offer these shirts in Mens Sizes - Small, Medium, Large and X-Large.

In the Notes section of checkout please specify the size you would like.
Part #: 00-0002
USD$37.95 ea

Carb Stabilizer Bracket

Carburetor Stabilizer Bracket. These high quality made in Canada stainless steel brackets stabilize the carburetors when the air box is removed. A must have for pods or hard tails!

Fits: Honda CB750K (1969-76)
Part #: 12-0100
USD$49.95 Set/2

Chain Adjuster Stopper Set/2

Chain Adjuster Stopper Set/2. High quality made in Canada stainless steel stoppers. These have been discontinued by Honda get these stainless steel upgrades today! Replaces OEM# 52136-405-000 and 52136-ME1-670.

Fits: Honda CB750K (1977-78),
CB750F (1977-78) Supersport,
CB750A (1977-78) Hondamatic
Part #: 12-0101
USD$94.95 Set/2

Stock Type Ignition Coil Set/2 With Brackets

Stock Type Ignition Coil Set/2 With Brackets. Replaces OEM# 30500-300-013

Dual Coil Assembly Pre-Mounted on their Brackets Just Like the Stock Type. Plug and Play Easy Install. Primary 4.3 Ohm, Secondary 15,000k Ohms.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 65-6507
USD$1.45 ea

Kick Stand Stopper Rubber

Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.

Fits: Honda CB750K (1969-78),
CB750A (1976-78) Hondamatic,
CB750F (1978) Supersport
Part #: 07-4624
USD$54.95 ea

Adjustable Fork Seal Driver 35-45mm

Adjustable 35-45mm Fork Seal Driver. This high quality tool can be used on many different fork sizes. Use these for easy installation of most fork seals on either conventional or inverted forks.

35mm Forks used on Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 35-3041
USD$20.95 ea

Performance Tool Spark Plug Crimper Tool

Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Part #: 07-9977
USD$89.95 ea

Dynatek Charge Monitor

Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems.

The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing.

High quality made in the USA. Comes with a one year warranty through the manufacturer.
Part #: 07-9976
USD$27.70 Set

Dynatek Performance Spark Plug Wire Set

Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core.

4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user.

Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA.

Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Part #: 07-9978
USD$194.95 Set/2

Dynatek Performance High Output 3 Ohm Ignition Coil Set/2

Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9980
USD$217.45 Kit

Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires

Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user.

Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9974
USD$194.95 Set/2

Dynatek Performance High Output 5 Ohm Ignition Coil Set/2

Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek.

These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions.

Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Part #: 07-9979
USD$209.95 Kit

Dynatek Dyna S Ignition System

Dynatek Dyna S Ignition System.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

This ignition can be used with your stock coils or any other coils 3 ohms or higher. Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9988
USD$359.95 Kit

Dynatek Dyna S Ignition System (Premium Kit)

Dynatek Dyna S Ignition System (Premium Kit) with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9987
USD$412.45 Kit

Dynatek Dyna S Ignition System (Ultimate Kit)

Dynatek Dyna S Ignition System (Ultimate Kit) with Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna S is a complete self-contained electronic ignition system built with the latest state-of-the-art engineering. This is the same ignition used by top racers over the past 2 decades. The Dyna S is completely housed behind the ignition cover and uses a magnetic rotor with the original spark advancer, so the factory advance curve is maintained. Increases power and reduces vibration, backfiring and intake reversion, especially on engines with radical cam timing. Front and rear cylinder timing may be set individually. Perfect for hot dual-plugged engines.

The Dyna S ignition is a time proven solution to the basic ignition and trigger needs of the modern motorcycle. The Dyna S is the standard of performance and reliability. Very high quality made in the USA.

Includes instructions and comes with a one year warranty through Dynatek.

Fits: Honda CB750K (1969-78),
CB750F (1975-78) Supersport,
CB750A (1976-78) Hondamatic
Part #: 07-9986
USD$472.45 Kit

Dynatek Dyna 2000 Digital Performance Ignition

Dynatek Dyna 2000 Digital Performance CDI Ignition.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions. Comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9994
USD$584.95 Kit

Dynatek Dyna 2000 Digital Perfomance Ignition (Premium Kit)

Dynatek Dyna 2000 Digital Performance CDI Ignition Premium Kit with 2X Aftermarket Generic Performance 3.3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9993
USD$674.25 Kit

Dynatek Dyna 2000 Digital Perfomance Ignition (Ultimate Kit)

Dynatek Dyna 2000 Digital Performance CDI Ignition Ultimate Kit with 2X Dynatek Brand 3 Ohm Dual Output Coils and Dynatek Brand High Performance Spark Plug Wires.

The Dyna 2000 Digital Performance Ignition represents a breakthrough in motorcycle ignition flexibility. The Dyna 2000 system consists of a state of the art microprocessor controlled ignition module along with an adjustable Dyna dual sensor crank trigger. For the first time you can actually set the ignition timing to what you want to maximize engine performance. A number of different advance curve modes and a broad range rev limiter lets you tailor the ignition to your needs. Up to a 7 horsepower increase! This is a very high quality kit that will increase the performance of your bike! Made in the USA.

Features - 5 Different adjustable timing curves, 4 Different retard modes, Fully static time-able with built in LED light (Set the timing accurately without having the engine running), Broad range rev limiter (8,500 to 16,000), Increased horsepower & torque, Digital tach output (smooth & accurate), Increased spark energy, Improved throttle response & easier starting, Easy mounting.

Includes the Dyna 2000 unit, complete wiring harness, ignition plate unit with rotor and full instructions, 2X Dynatek 3 Ohm coils, Dynatek spark plug wire set. Ignition unit comes with a one year warranty from Dynatek.

Fits: Honda CB750K (1969-78)
CB750F (1975-78) Supersport
Part #: 07-9992
USD$37.96 ea

High Performance Kibblewhite Black Diamond Intake Valve

High Performance Kibblewhite Black Diamond Intake Valve. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years.

All Black Diamond Stainless steel valves are impregnated by a special German process to a depth of .002, with a surface build up of .0002. This Black Diamond process improves wear properties, reduces friction, and provides resistance to corrosion and wear that is superior to chrome and nickel electrolysis plating.

Each valve is designed using Finite Element Analysis software, and profiles are tested on our computerized flow bench. Black Diamond Valves are lightweight, strong, one piece forgings with profiles that provide excellent flow characteristics.

Fits: Honda CB750F (1977-78) Supersport

Sold Each, Order the Quantity you Require
Part #: 01-9948
USD$37.96 ea

High Performance Kibblewhite Black Diamond Exhaust Valve

High Performance Kibblewhite Black Diamond Exhaust Valve. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years.

All Black Diamond Stainless steel valves are impregnated by a special German process to a depth of .002, with a surface build up of .0002. This Black Diamond process improves wear properties, reduces friction, and provides resistance to corrosion and wear that is superior to chrome and nickel electrolysis plating.

Each valve is designed using Finite Element Analysis software, and profiles are tested on our computerized flow bench. Black Diamond Valves are lightweight, strong, one piece forgings with profiles that provide excellent flow characteristics.

Fits: Honda CB750F (1977-78) Supersport

Sold Each, Order the Quantity you Require
Part #: 01-9949
USD$121.56 Set

High Performance Kibblewhite Valve Spring Set

High Performance Kibblewhite Valve Spring Set of 8. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years.

The springs in these kits are wound from super clean chrome silicon wire that has been heat treated and shot peened. These components offer optimal fitment, keeping lateral movement to a minimum. They work together as a system, providing long life, and maximum performance.

Fits: Honda CB750F (1977-78) Supersport
Part #: 01-9947
USD$15.95 ea

CB Premium Chrome Mirror - Original Type - DOHC - Short 5" Stem

Mirror - Honda Premium Chrome - 5" Stem, 10mm. RH threads. Replaces OEM #88110-438-003 Except these are shorter then stock.

Will also fit Any Honda: CB

Note: These Fit Both Left And Right Side Of Bike, Order 2 For A Complete Set
Part #: 16-4668
USD$64.95 ea

Handlebar - Chrome

Z Handlebar - Chrome
Total Width 24.25" - Middle Inner Width 6" - Rise/Height 6" x 7/8"Dia.

Note: Not Drilled for wires
Part #: 25-0146
USD$79.95 ea

Front Brake Master Cylinder Assembly

Out of Stock
Email Me When Available
Front Brake Master Cylinder Assembly
Front Brake Master Cylinder Assembly. You can use it on any single or dual disc brake.

Black body with black lever. Features a piston size of 15.8mm. These include a brake light switch with two small spade connectors. These are not identical to the stock type but will work great!
Part #: 08-0457
USD$34.95 Set

High Performance Kibblewhite Bronze Swingarm Bushing Set

High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years.

Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.

Fits: Honda CB750K (1976-78)
Part #: 28-1038